Home > Error Code > 0142 Error Code Dell

0142 Error Code Dell

Contents

To confirm this, First boot into Setup (Bios) by pressing F2. If you require further assistance, please contact Technical Support. Instructions for BIOS updates vary by manufacturer and should be followed cautiously. For further information on running the online diagnostics, please refer to the article How to use the Dell Online Diagnostic Tool to troubleshoot your Dell PC for more information. http://webtooz.com/error-code/0142-dell-error-code.html

An error occurred during the tests that may involve the main system board of the system. Repeat the PSA diagnostics. You can get more information on possible resolutions to your issue and even get a part dispatched if needed. Repeat the PSA diagnostics.

Hard Drive Error Code 0142 Repair Tip

PSA NA ePSA 2000-0133 Battery - The battery cannot supply sufficient power. Error occurs when a graphics test times out while waiting for you to enter a response. Update to the latest BIOS. If there is video on the LCD, then the Display does not need replacement.

Update to the latest BIOS. Note: Notebooks may have either PSA or ePSA diagnostics, depending on their age. Repeat the PSA diagnostics. Hard Drive Error Code 2000-0146 Repeat the PSA diagnostics.

Shop Support Community My Account Shop Support Community ×Close Knowledge Base English العربية Česky Dansk Deutsch Español Suomi Français Italiano 日本語 한국어 Nederlands Norsk Polski Português Русский Svenska Türkçe 简体中文 Resolve Dell Validation Code Update to the latest BIOS. Repeat the PSA diagnostics. http://www.dell.com/support/article/us/en/4/SLN115162/en If no 2000-0123 memory error occurs, and if diagnostics fail again after the BIOS is at the most current version, visit our ePSA online tool.

Update to the latest BIOS. Error Code 2000-0142 Status 7 Try a known good USB device. You can get more information on possible resolutions to your issue and even get a part dispatched if needed. A is the non existent floppy B is a tiny drive of a few MB (??) C is actually a virtual RAM drive with HIMEN.SYS loaded into it.

Dell Validation Code

If a memory error is detected, try memory modules individually. http://www.techsupportforum.com/forums/f16/error-code-2000-0142-a-964769.html Power down system and reseat memory. Hard Drive Error Code 0142 Repair Tip PSA NA ePSA 2000-0714 Heat Sink - Heat sink clip not installed. Dell Hard Drive Error Code 2000-0151 If a memory error is detected, try memory modules individually.

What can I do!? 16 commentsshareall 16 commentssorted by: besttopnewcontroversialoldrandomq&alive (beta)[–]indecisiveredditor 1 point2 points3 points 3 years ago(3 children)If this is a utility from Dell, then I would assume it has detected errors in navigate here If diagnostics fail again after the BIOS is at the most current version, visit our ePSA online tool. Can you run the DST, PSA and ePSA diagnostics on already encrypted Full Drive Encryption (FDE) drives? Q: What does "semper fi" mean? Dell Hard Drive Error Code 0146

You can get more information on possible resolutions to your issue and even get a part dispatched if needed. The ePSA utility will start to run. Repeat the PSA diagnostics. http://webtooz.com/error-code/0142-dell-code.html Or you can tap the F12 key at the Dell splash screen on start-up.

Update the BIOS to the most current version and the issue should resolve. Error Code 2000-0142 Validation PSA NA ePSA 2000-0315 Sensor - the (s) reading (dc) is lower than expected The system board or ssensor is failing the diagnostic tools. Turn off your computer and remove and replace the battery (see your service manual for instructions).

Go to the the Dell Support Site.

You can get more information on possible resolutions to your issue and even get a part dispatched if needed. PSA NA ePSA 2000-0245 System board - USB device timeout waiting for the device to respond An error occurred during the tests that may involve the USB controller or ports of ePSA Timer - Interval timer not functional. Dell Validation Code Generator Update to the latest BIOS.

If the diagnostics still results in an error code, visit our ePSA online tool. Repeat the PSA diagnostics. Turn off your computer and connect the cable that is described in the string portion of the message (see your service manual for instructions). http://webtooz.com/error-code/0142-error-code.html If the diagnostics still results in an error code, visit our ePSA online tool.

PSA NA ePSA 2000-8014 Diagnostics - ADDF module ([s]) device ([s]) failed with error code [x], number [x]. Repeat the PSA diagnostics. If diagnostics fail again after the BIOS is at the most current version, contact Technical Support to resolve the problem. Reseat the drive is a portable, reseat the data cable at both ends and the power connection if a desktop then repeat the PSA diagnostics.

Repeat the PSA diagnostics. permalinkembedsaveparentgive gold[–]griffmundo 0 points1 point2 points 3 years ago(0 children)Yes I am aware of this I was just spelling it out correctly as the command sounds. Update to the latest BIOS. Next Steps PSA NA ePSA 2000-0111 CPU - Exception occurred.

The motherboard BIOS revision may not be current. If the diagnostics still results in an error code, visit our ePSA online tool. Please try the request again. If the diagnostics still results in an error code, visit our ePSA online tool.

Unable to [s] testable memory. If a memory error is detected, try memory modules individually. If the diagnostics still results in an error code, visit our ePSA online tool. Repeat the PSA diagnostics.

Repeat the PSA diagnostics. Take nice care of yourselves - Paul - ♪ - Help to start using BiNG. You can get more information on possible resolutions to your issue and even get a part dispatched if needed. The 2000-0326 and 2000-0415 errors can also be reported in error with certain LCD cables installed.

You can get more information on possible resolutions to your issue and even get a part dispatched if needed. Clear the log.